1. MANUFACTURERS RECOMMENDED WINTERIZATION/SPRING SERIVCE PACKAGE FOR I/O'S AND INBOARDS
*Some engines may have block plugs removed*

FALL: Fog engine with a rust prevention solution through-out engine and fuel system to protect internal engine parts. Circulate non-toxic antifreeze through the engine cooling system. Change engine oil and filters using only quality products. Drain and refill lower unit lubricant, pressure and vacuum test lower unit if any indications of water exist, notify customer if present. Apply anticorrosive grease to outdrive fittings, shift and throttle linkages. Add fuel stabilizer to fuel tank(s) as required per gallon.

SPRING: Check and top off engine oil and lower unit lubricant due to settling, start engine and clear rust preventative solution, spot check hoses, belts, shifting, adjust idle speed and more.

ALL PARTS & MATERIALS INCLUDED

COMPLETE PACKAGE PER ENGINE: $199.95

2. OUTDRIVE SEASONAL SERVICE PACKAGE

This service is recommended annually by marine engine manufacturers!

Removal of outdrive from watercraft.

Inspection of gimbal bearing and universal joints.

Check and inspect exhaust, universal and shift bellows.

Grease u-joints and pivot points.

Reinstall outdrive with new gasket and o-ring set as required.

Water pump recommended to be serviced annually

3. WATER SYSTEM WINTERIZATION

FALL: Disconnect hose connections as necessary and drain fresh water system, including sinks, water heater and showers. Add and circulate non-toxic antifreeze. Toilet and holding tank winterized with permanent type antifreeze.

SPRING: Connect water system connections and make ready for use. Purge fresh water system and fill water tank.

ALL MATERIALS ARE INCLUDED

PACKAGE PRICE: $99.00

4. GENERATOR WINTERIZATION

Fog engine with a rust prevention solution. Circulate non-toxic antifreeze through the engine cooling system as needed. Change engine oil/filter as required. Startup in spring.

PACKAGE PRICE: $149.95

5. EXTRAS

Oil and Filter	$75.00 plus materials
Propeller Repair	$75.00 plus repairs

6. HAUL OUT, POWER WASH, BLOCK and LAUNCH 

Lift watercraft from water or trailer, power wash bottom and drive units, block on boats stands and re- launch.

PRICE: $7.50 per linear foot

7. LIVEWELL WINTERIZATION

Purge live-well plumbing and circulate NON-toxic antifreezes as needed.

PRICE: $34.95

1. Run engine and fog with rust prevention solution thru-out engine and fuel system to protect all internal engine parts.
2. Add fuel stabilizer to fuel tank(s) as required per gallon, to preserve fuel for next season's enjoyment.
3. Apply anticorrosive grease to all fittings and linkages, including steering cable.
4. Drain lower unit lubricant as applicable, pressure and vacuum test lower unit if any indications of water exist, notify customer if present. Fill lower unit with new lubricant.
5. Change crankcase oil and filter on all 4 stroke outboards as applicable.
6. Flush cooling system with non-toxic antifreeze on all jet drives as applicable.

ALL MATERIALS ARE INCLUDED

SPRING STARTUP AND EVALUATION

1. Top off lower unit lubricant due to settling.
2. Start engine with pre-mix gas, cleaning rust preventative solution.
3. Inspect oil lines and clean oil filter on all injected motors as applicable.
4. Check shift operation, linkage and control cables.
5. Inspect fuel filter, fuel lines, replace o-ring.
6. Adjust idle speed.
7. Top off crankcase oil on all 4 stroke outboards.
8. Suggest needed or advisable repair services.
   $20.00 charge for no gas, no keys or no battery. Gas cost additional.

OPTIONAL:

Special priced spring tune up for our winterizing customers.

START

LOOSE

TAPED

FINISHED

Shrink Wrap Boat Storage!
This innovative, inexpensive and safe winter storage method for marine and small vehicles is now available here at Crown Pointe Marina! We've provided some information below. If you have any other questions, please feel free to give us a call.

What is Shrink-wrap Storage?
Shrink-wrap Storage is the same method that many manufacturers use on their boats and other marine vehicles when transporting them from factory to the retailer or customer. In a nutshell: The boat/vehicle is covered in plastic (a frame is built inside the boat to lift the plastic away from interior spaces), the plastic is tied around the bottom of the boat, and then the entire thing is heated and shrunk to mold itself to the contours of the vessel, allowing for the best possible protection against wind and rain.

Will moisture build up?
Vents are installed that enable air to flow through the interior without letting moisture in to keep the interior dry.

Will the plastic wrap scar or mar the finish of my boat?
No. This is the same technology many manufacturers use to protect the finish during transport. Because the heat shrink process creates such a tight fit, there is no movement of the shrink-wrap to cause abrasion when the boat is being moved.

How much does it cost?
Shrink-wrap storage is priced by the linear foot (the length of your boat). The cost is $10 per linear foot for v-hull boats and $14 per linear foot for boats with t-tops, hard tops and fly bridges. If you have an outboard motor the shrink-wrap will also cover that. At $10 a linear foot, the cost to shrink-wrap a 20 foot v-hull boat would be $200.

What can't I just use a tarp or put it in my old barn, etc?
Tarps degrade and do not protect well against small windborne objects (i.e. twigs, dust, leaves). This is a nice heavy-gauge plastic that will aid significantly in protecting your vessel from the elements. Storing your boat in a clean, dry facility is always an option (although usually a more expensive one). If the facility where your boat is stored is not clean and dry you may find tough-to-remove mold and mildew on the interior surfaces when you get your boat out of storage in the spring. Some storage sheds are dry but not protected from dirt and dust. Having your boat properly shrink-wrapped will allow you to store it outside when dry indoor space is not available.



Fast & easy getting back on the water in the spring
Our goal in shrink-wrapping your boat for storage is to provide a dry, clean method of storage. We will be happy to clean the interior of your boat prior to shrink-wrapping. When you are ready to get back on the water, the only thing that we will have to do is remove the shrink-wrap, charge the battery, and wave as you head out into the bay.

---